How JustAnswer Works:
  • Ask an Expert
    Experts are full of valuable knowledge and are ready to help with any question. Credentials confirmed by a Fortune 500 verification firm.
  • Get a Professional Answer
    Via email, text message, or notification as you wait on our site.
    Ask follow up questions if you need to.
  • 100% Satisfaction Guarantee
    Rate the answer you receive.
Ask JOHN aka Eauto Your Own Question
JOHN aka Eauto
JOHN aka Eauto, The Car Guy
Category: Chevy
Satisfied Customers: 15068
Experience:  ase tech
6149662
Type Your Chevy Question Here...
JOHN aka Eauto is online now
A new question is answered every 9 seconds

1998 Chevy Malibu: i need to check the transmission fluid

Resolved Question:

how often do i need to check the transmission fluid on my 1998 Chevy Malibu?
Submitted: 7 years ago.
Category: Chevy
Expert:  JOHN aka Eauto replied 7 years ago.
Transmission Fluid Checking Produce (Oil Level Check)
Notes

TRANSMISSION FLUID CHECKING PRODUCE (OIL LEVEL CHECK)

Checking Oil Level

Oil Fill And Vent Cap - 4T40E Transaxle



The fluid level screw is intended to be used for diagnosing a transaxle fluid leak or resetting the transaxle fluid level after service that involves a loss of fluid.

Inspect

The fluid level should be checked when the transaxle is near Room temperature or at 40°C (104°F) .

CAUTION: Removal of the fluid level screw when the transaxle fluid is hot may cause injury. Use care to avoid contact of transaxle fluid to exhaust pipe.

The engine must be running when the transaxle fluid level screw is removed, or excessive fluid loss will occur. Since the actual fluid level is unknown, stand clear when removing the fluid level screw. Have a container ready to capture any lost fluid.

WARNING: Do not turn the engine off with the fluid level screw removed as you can be injured by hot transaxle fluid being expelled out of the fluid check hole.

  1. Let vehicle idle for three to five minutes with accessories off.
  2. Apply brake
  3. Move shift lever through all gear ranges, pausing three seconds in each range.
  4. Place shift lever in Park. Important: Vehicle must be kept level on the hoist.
  5. Raise vehicle on hoist.
  6. Place oil container under fluid level screw.
  7. Remove the fluid level screw with the engine running at idle.
  8. Fluid level should be at the bottom of the fluid check hole. Because the transaxle operates correctly over a range of fluid levels, fluid may or may not drain out of the fluid check hole when the fluid level screw is removed. If fluid drains through the fluid check hole, this transaxle may have been overfilled. When fluid stops draining, the fluid level is correct and the fluid level screw may be installed. If fluid does not drain through the fluid check hole, the transaxle fluid level may be low. Proceed to ADDING TRANSAXLE FLUID.
  9. Install fluid level screw. Tighten 12 N.m (106 lb in)
  10. Lower vehicle.
  11. Shut off engine. Adding Transaxle Fluid: With the engine running, add fluid at the vent cap location in half liter (1 pint) increments until fluid drains through the fluid check hole. Allow the fluid to finish draining through the fluid check hole.
  1. Install fluid level screw. Tighten 12 N.m (106 lb in)
  2. Lower vehicle.

 

 

JOHN aka Eauto and 4 other Chevy Specialists are ready to help you
Customer: replied 7 years ago.
Okay, so that's how to do it, but how often does it need to be done? Once every how many miles?
Expert:  JOHN aka Eauto replied 7 years ago.
Well once a year is a good rule of thumb also the fluid and filter should be changed every 50k
Customer: replied 7 years ago.
so, as I don't have a hoist, I need to take this to a technician?
Expert:  JOHN aka Eauto replied 7 years ago.
That would be the best way because the car needs to be level

Related Chevy Questions