How JustAnswer Works:
  • Ask an Expert
    Experts are full of valuable knowledge and are ready to help with any question. Credentials confirmed by a Fortune 500 verification firm.
  • Get a Professional Answer
    Via email, text message, or notification as you wait on our site.
    Ask follow up questions if you need to.
  • 100% Satisfaction Guarantee
    Rate the answer you receive.
Ask Tim's Auto Repair Your Own Question
Tim's Auto Repair
Tim's Auto Repair, mechanic
Category: Chevy
Satisfied Customers: 15477
Experience:  Have owned a repair shop for 25 yrs.
14541291
Type Your Chevy Question Here...
Tim's Auto Repair is online now
A new question is answered every 9 seconds

1994 chevy: trying to bleed the rear brakes..to com out of the fitting

Customer Question

i have been trying to bleed the rear brakes on my 1994 chevy silverado but i can hardly get any fluid at all to com out of the fitting when i try. the front ones have a great stream of fluid coming out. what am i doing wrong. i have tried both sides about 25 to 30 times each?
Submitted: 7 years ago.
Category: Chevy
Expert:  Tim's Auto Repair replied 7 years ago.

hi

lets try this...abs bleeding can be hateful

thanks

please ACCEPT my answer so I can get credit for my work.i don't receive commission unless you do ..i'm not always going to be giving you good news,so please dont let this stand in the way of you accepting my answer.it does not cost you more money.we will still be able to communicate.. Bonuses and positive feedback are appreciated!if you are not satisfied with my answer,please do not leave bad feed back,i will gladly opt out and let another expert handle the question.PLEASE ASK IF YOU NEED MORE HELP

ABS Bleed Procedure

Important:

  • Use the two-person bleed procedure under the following conditions:
  • Installing a new Electro-Hydraulic Control Unit (ECU) or new Brake Pressure Modulator Valve (BPMV).
  • Air is trapped in the valve body.
  • Do not drive the vehicle until the brake pedal feels firm.
  • Do not reuse brake fluid that is used during bleeding.
  • Use the vacuum, the pressure and the gravity bleeding procedures only for base brake bleeding.

TWO PERSON PROCEDURE

  1. Raise the vehicle in order to access the system bleed screws.
  2. Bleed the system at the right rear wheel first.
  3. Install a clear hose on the bleed screw.
  4. Immerse the opposite end of the hose into a container partially filled with clean DOT 3 brake fluid.
  5. Open the bleed screw 1/2 to one full turn.
  6. Slowly depress the brake pedal. While the pedal is depressed to its full extent, tighten the bleed screw.
  7. Release the brake pedal and wait 10-15 seconds for the master cylinder pistons to return to the home position.
  8. Repeat the previous steps for the remaining wheels. The brake fluid which is present at each bleed screw should be clean and free of air.
  9. This procedure may use more than a pint of fluid per wheel. Check the master cylinder fluid level every four to six strokes of the brake pedal in order to avoid running the system dry.
  10. Press the brake pedal firmly and run the Scan Tool Automatic Bleed Procedure. Release the brake pedal between each test.
  11. Bleed all four wheels again using Steps 3-9. This will remove the remaining air from the brake system.
  12. Evaluate the feel of the brake pedal before attempting to drive the vehicle.
  13. Bleed the system as many times as necessary in order to obtain the appropriate feel of the pedal.
Hydraulic Brake System Bleeding

 



If air has entered the hydraulic brake system, bleed the system. You may need to bleed the hydraulic brake system at all four wheels due to one of the following conditions:

 

  • Air entered the system due to a low fluid level.
  • The brake pipes have been disconnected at the master cylinder.
  • The brake pipes have been disconnected at the combination valve.

If a pipe is disconnected at one wheel, then only bleed that wheel.

If the master cylinder has been removed, bleed the master cylinder before installing it on the vehicle. This will reduce the time required to bleed the system.

NOTICE: Brake fluid will damage electrical connections and painted surfaces. Use shop cloths, suitable containers, and fender covers to prevent brake fluid from contacting these areas. Always re-seal and wipe off brake fluid containers to prevent spills.

MANUAL BLEEDING

  • Tools Required
  • J 28434 Wheel Cylinder Bleeder Wrench.
  1. If the vehicle has a vacuum booster, apply the brakes several times with the ignition OFF. This relieves the vacuum reserve.
  2. Fill the master cylinder reservoir. Use Delco Supreme 11 Hydraulic Brake Fluid, or equivalent DOT 3 motor vehicle brake fluid. Maintain the fluid level during bleeding.
  3. If the master cylinder has air in the bore, bleed the master cylinder using the following procedure:
3.1.Disconnect the forward brake pipe connector at the master cylinder.
3.2.Allow the brake fluid to flow from the connector port.
3.3.Connect the brake pipe connector. Do not tighten the brake pipe connector.
3.4.Slowly apply the brake pedal. Allow the air to bleed from the loose connector.
3.5.Tighten:the connector before releasing the brake pedal.
3.6.Wait 15 seconds.
3.7.Repeat this sequence, including the 15-second wait, until you purge all the air from the master cylinder bore.
3.8.Repeat this procedure for the rear brake pipe after you purge all the air from the forward pipe connection.
  1. If you replaced the Brake Pressure Modulator Valve of the 4WAL system, or if you suspect that air is trapped inside, bleed the Brake Pressure Modulator Valve next.
  2. Using J28434, bleed each wheel cylinder in the following sequence:
5.1.Right rear wheel cylinder
5.2.Left rear wheel cylinder
5.3.Right front wheel caliper
5.4.Left front wheel caliper
  1. Attach a hose to the wheel cylinder/caliper bleeder valve.
  2. Immerse the opposite end of the hose into a container partially filled with clean brake fluid.
  3. Slowly apply the brake pedal one time and hold.
  4. Loosen the bleeder valve in order to purge the air from the wheel cylinder/caliper.
  5. Tighten:the bleeder valve.
    • Tighten the bleeder valve to 13 Nm (110 inch lbs.) .

NOTICE: Refer to Fastener Notice in Service Precautions.

  1. Slowly release the brake pedal.
  2. Wait 15 seconds.
  3. Repeat this sequence, including the 15-second wait, until you purge all the air from the wheel cylinder or caliper.
  4. Repeat steps 6-12 at each wheel until you purge all the air from the brake system.
  5. Check the brake pedal for sponginess. Check the brake warning lamp for an indication of unbalanced pressure. Repeat the bleeding procedure in order to correct either of these conditions.

 



PRESSURE BLEEDING

 

  • Tools Required
  • J 29567 Brake Bleeder Adapter
  • J 28434 Wheel Cylinder Bleeder Wrench

Use a diaphragm-type pressure bleeder. The pressure bleeder must have a rubber diaphragm between the air supply and the brake fluid. This prevents air, moisture, oil and other contaminants from entering the brake hydraulic system.

  1. Fill the pressure tank at least 2/3 full of brake fluid.
  2. Bleed the bleeder each time you add fluid.
  3. Charge the bleeder to 140-170 kPa (20-25 psi).
  4. Install the J29567 Brake Bleeder Adapter.
  5. If the Brake Pressure Modulator Valve of the 4WAL system is replaced, or if you suspect that air is trapped inside, bleed the Brake Pressure Modulator Valve first.
  6. Using J 28434, bleed each wheel cylinder or caliper in the following sequence:
6.1.Right rear wheel cylinder
6.2.Left rear wheel cylinder
6.3.Right front wheel caliper
6.4.Left front wheel caliper
  1. Connect the hose from the bleeder to the adapter at the master cylinder.
  2. Open the tank valve.
  3. Attach a hose to the bleeder valve.

 



 

  1. Immerse the opposite end of the hose into a container partially filled with clean brake fluid.
  2. Slowly open the bleeder valve at least 3/4 of a turn. Allow the fluid to flow until you see no air in the fluid.
    • Tighten the wheel cylinder or caliper bleeder valve to 13 Nm (110 inch lbs.) .

NOTICE: Refer to Fastener Notice in Service Precautions. Check the brake pedal for sponginess. Repeat the bleeding procedure if the brake pedal is spongy.

  1. Repeat steps 9-12 at every wheel.
  2. Disconnect the hose from the bleeder adapter.
  3. Remove the J 29567 Brake Bleeder Adapter.
  4. Fill the master cylinder to the proper level.

Related Chevy Questions