How JustAnswer Works:
  • Ask an Expert
    Experts are full of valuable knowledge and are ready to help with any question. Credentials confirmed by a Fortune 500 verification firm.
  • Get a Professional Answer
    Via email, text message, or notification as you wait on our site.
    Ask follow up questions if you need to.
  • 100% Satisfaction Guarantee
    Rate the answer you receive.
Ask Butch Your Own Question
Butch, Master ASE Certified Technician
Category: Chevy
Satisfied Customers: 375
Experience:  Master ASE Certified Technician, 10 years experience, 60+ GM certificates, 150+ GM training courses
Type Your Chevy Question Here...
Butch is online now
A new question is answered every 9 seconds

How do i change the injectors in a 2000 s10 4.

This answer was rated:

how do i change the injectors in a 2000 s10 4.3 engine vin 1gccs19w5y8103383


Here is the complete procedure, please read it carefully. If you have any more questions, please ask.

Fuel Injector Replacement

Removal Procedure

    Object Number: 585444  Size: MH

    Caution: Unless directed otherwise, the ignition and start switch must be in the OFF or LOCK position, and all electrical loads must be OFF before servicing any electrical component. Disconnect the negative battery cable to prevent an electrical spark should a tool or equipment come in contact with an exposed electrical terminal. Failure to follow these precautions may result in personal injury and/or damage to the vehicle or its components.

  1. Disconnect the negative battery cable.
  2. Relieve the fuel system pressure.
  3. Remove the upper intake manifold assembly.
  4. Remove the fuel meter body assembly.
  5. Remove the injector assembly retainer (11) and the injector retainer lock nuts (10).

    Notice: Use care in removing the fuel injectors to prevent damage to the electrical connector terminals.

    The fuel injector is serviced as a complete assembly only.



    Also since the injectors are electrical components, these injectors should not be immersed in any type of liquid solvent or cleaner as damage may occur. Fuel injector cleaning is not recommended.



  6. While pulling the poppet nozzle tube downward, push with a small tip punch down between the injector terminals until the injector is removed.

Installation Procedure

Important: Each injector is calibrated for a specific flow rate. Order the correct injector for the application being serviced when replacing the fuel injectors.

    Object Number: 331936  Size: SH

  1. Lubricate the new injector O-ring seals with clean engine oil (2).
  2. Install the O-rings on the injector assembly (2).
    Object Number: 585444  Size: MH

  3. Install the fuel injector assembly (12) into the fuel meter body injector socket.

    Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

  4. Install the injector assembly retainer (11) and the injector retainer lock nuts (10).

    Tighten the injector retainer lock nuts to 3.0 N·m (27 lb in).

  5. Install the fuel meter body assembly.
  6. Install the upper intake manifold assembly.
  7. Tighten the fuel filler cap.
  8. Connect the negative battery cable.
  9. Inspect for leaks.
    9.1. Turn the ignition switch ON for 2 seconds.
    9.2. Turn the ignition switch OFF for 10 seconds.
    9.3. Turn the ignition switch ON.
    9.4. Inspect for fuel leaks.
Butch and 2 other Chevy Specialists are ready to help you

Related Chevy Questions