How JustAnswer Works:
  • Ask an Expert
    Experts are full of valuable knowledge and are ready to help with any question. Credentials confirmed by a Fortune 500 verification firm.
  • Get a Professional Answer
    Via email, text message, or notification as you wait on our site.
    Ask follow up questions if you need to.
  • 100% Satisfaction Guarantee
    Rate the answer you receive.
Ask Tim's Auto Repair Your Own Question
Tim's Auto Repair
Tim's Auto Repair, Mechanic
Category: Car
Satisfied Customers: 15465
Experience:  Have owned a repair shop for 25 yrs.
14541291
Type Your Car Question Here...
Tim's Auto Repair is online now
A new question is answered every 9 seconds

RA crb

Customer Question

The heater fan motor does not turn with the sw. But will come on when i run over a bump in the road. Do i need to replace the fan motor? How is this done?
Submitted: 4 years ago.
Category: Car
Expert:  Tim's Auto Repair replied 4 years ago.

tims auto repair :

hi

tims auto repair :

first,,check the wire harness plugs to the resister and to the blower moter first

tims auto repair :

it may not be getting a good connection,,

tims auto repair :

BLOWER MOTOR RESISTOR REPLACEMENT - AUXILIARY

REMOVAL PROCEDURE
1. Remove the right console accessory trim plate.








14_gc-493725.png
Full Size Image


2. Disconnect the electrical connector (3) from the blower resistor (2).
3. Remove the screws (1) that retain the auxiliary blower motor resistor (2).








12_gc-493721.png
Full Size Image


4. Remove the auxiliary blower motor resistor from the vehicle.

INSTALLATION PROCEDURE








12_gc-493721.png
Full Size Image


1. Install the auxiliary blower motor resistor.








14_gc-493725.png
Full Size Image


2. Install the auxiliary blower motor resistor screws (1).

Tighten the screws to 1.4 N.m (13 lb in).



3. Connect the electrical connector (3) to the auxiliary blower motor resistor (2).
4. Install the console trim plate.

tims auto repair :

BLOWER MOTOR REPLACEMENT

REMOVAL PROCEDURE
1. Remove the right side sound insulator.








82_gc-291175.png
Full Size Image


2. Remove the instrument panel (I/P) compartment.
3. Remove the dash integration module (DIM) from the bracket.
4. Remove the 2 rear DIM bracket fasteners.
5. Reposition the DIM bracket in order to remove the blower motor.








77_gc-828429.png
Full Size Image


6. Disconnect the electrical connector (1) from the blower motor.
7. Disconnect the blower motor ventilation tube (2) from the module.








79_gc-828431.png
Full Size Image


8. Remove the blower motor retaining fasteners (1).
9. Remove the blower motor from the vehicle.

INSTALLATION PROCEDURE








79_gc-828431.png
Full Size Image


1. Install the blower motor into the blower motor housing.
2. Ensure that the blower motor gasket is properly aligned.
3. Install the blower motor retaining screws (1).

Tighten the screws to 1.4 N.m (12 lb in).

NOTE: Refer to Fastener Notice in Service Precautions.








77_gc-828429.png
Full Size Image


4. Connect the electrical connector (1) to the blower motor.
5. Connect the blower motor ventilation tube (2) to the module.








82_gc-291175.png
Full Size Image


6. Reposition the DIM bracket to its original position.
7. Install the 2 rear DIM bracket fasteners.
8. Install the DIM.
9. Install the I/P compartment.
10. Install the right side sound insulator.

tims auto repair :

Please RATE my answer by clicking the RATINGS button, so I can get credit for my work,,the [BAD SERVICE] and [POOR SERVICE] rating does not give me credit].i don't receive commission if you give a less than 3 star/smiley rating ..I'm not always going to be giving you good news,so please don't let this stand in the way of you accepting my answer.it does not cost you more money.we will still be able to communicate,,.please understand,i can not see,hear or touch the vehicle and only know what you tell me. Bonuses and positive feedback are appreciated!if you are not satisfied with my answer,please do not leave bad feed back,i will gladly opt out and let another expert handle the question.if i have sent any diagrams,please print them.they will only stay on here for an hour or so...sometimes you may need to right click the image,then save picture as]to save it to your computer so you can open it with your picture program...PLEASE ASK IF YOU NEED MORE HELP

Related Car Questions