How JustAnswer Works:
  • Ask an Expert
    Experts are full of valuable knowledge and are ready to help with any question. Credentials confirmed by a Fortune 500 verification firm.
  • Get a Professional Answer
    Via email, text message, or notification as you wait on our site.
    Ask follow up questions if you need to.
  • 100% Satisfaction Guarantee
    Rate the answer you receive.
Ask Tim's Auto Repair Your Own Question
Tim's Auto Repair
Tim's Auto Repair, Mechanic
Category: Car
Satisfied Customers: 15576
Experience:  Have owned a repair shop for 25 yrs.
14541291
Type Your Car Question Here...
Tim's Auto Repair is online now
A new question is answered every 9 seconds

Suzuki Reno S how to do the timing belt diagram for 05 Suzuki

Customer Question

how to do the timing belt diagram for 05 Suzuki Reno.
Submitted: 5 years ago.
Category: Car
Expert:  Tim's Auto Repair replied 5 years ago.

hi

this should help you

thanks

Please ACCEPT my answer so I can get credit for my work.i don't receive commission unless you do ..I'm not always going to be giving you good news,so please don't let this stand in the way of you accepting my answer.it does not cost you more money.we will still be able to communicate.. Bonuses and positive feedback are appreciated!if you are not satisfied with my answer,please do not leave bad feed back,i will gladly opt out and let another expert handle the question.if i have sent any diagrams,please print them.they will only stay on here for an hour or so.PLEASE ASK IF YOU NEED MORE HELP

 

 

Suzuki Forenza, Reno 2003-06

Timing Belt & Sprockets

  • REMOVAL & INSTALLATION

 

Removal & Installation



  1. Disconnect the negative battery cable.
  2. Disconnect the Manifold Air Temperature (MAT) sensor connector.
  3. Disconnect the air cleaner outlet hose from the throttle body.
  4. Disconnect the breather tube from the camshaft cover.
  5. Remove the air cleaner housing bolts.
  6. Remove the air cleaner housing.
  7. Remove the right front wheel.
  8. Remove the right front wheel well splash shield.
  9. Remove the serpentine drive belt.
  10. Remove the crankshaft pulley bolts and the crankshaft pulley.
  11. Remove the right engine mount bracket.
  12. Remove the front timing belt cover bolts.
  13. Remove the front timing belt cover.
  14. Using the crankshaft gear bolt, rotate the crankshaft clockwise until the timing mark on the crankshaft gear is aligned with the notch at the bottom of the rear timing belt cover.
  15. FIG : Aligning the timing mark on the crankshaft gear with the notch at the bottom of the rear timing belt cover.

    image

  16. FIG : Aligning the camshaft gears with the notches on the camshaft cover.

    image

  17. Align the camshaft gears with the notch on the camshaft cover.

  18. Remove the timing belt.
  19. Loosen the automatic tensioner bolt. Turn the hex-key tab to relieve belt tension.
  20. To install:

    1. Align the timing mark on the crankshaft gear with the notch on the bottom of the rear timing belt cover.
    2. Align the timing marks on the camshaft gears, using the intake gear mark for the intake gear and the exhaust gear mark for the exhaust gear.
    3. Install the timing belt.
    4. Turn the hex-key tab in a clockwise direction to tension the belt. Turn until the pointer aligns with the notch.
    5. Install the automatic tensioner bolt and tighten to 18 ft. lbs. (25 Nm).
    6. Rotate the crankshaft two full turns clockwise using the crankshaft pulley bolt.
    7. Recheck the automatic tensioner pointer.
    8. Install the front timing belt cover.
    9. Install the front timing belt cover bolts and tighten to 53 inch lbs. (6 Nm).
    10. Install the right engine mount bracket.
    11. Install the crankshaft pulley and tighten the crankshaft pulley bolts to 15 ft. lbs. (20 Nm).
    12. Install the serpentine drive belt.
    13. Install the right front wheel well splash shield.
    14. Install the right front wheel.
    15. Install the air cleaner housing.
    16. Install the air cleaner housing bolts and tighten to 89 inch lbs. (10 Nm).
    17. Connect the air cleaner outlet hose to the throttle body.
    18. Connect the breather tube to the camshaft cover.
    19. Connect the MAT sensor connector.
    20. Connect the negative battery cable
    21. .

Please ACCEPT my answer so I can get credit for my work.i don't receive commission unless you do ..I'm not always going to be giving you good news,so please don't let this stand in the way of you accepting my answer.it does not cost you more money.we will still be able to communicate.. Bonuses and positive feedback are appreciated!if you are not satisfied with my answer,please do not leave bad feed back,i will gladly opt out and let another expert handle the question.if i have sent any diagrams,please print them.they will only stay on here for an hour or so.PLEASE ASK IF YOU NEED MORE HELP

Related Car Questions