How JustAnswer Works:
  • Ask an Expert
    Experts are full of valuable knowledge and are ready to help with any question. Credentials confirmed by a Fortune 500 verification firm.
  • Get a Professional Answer
    Via email, text message, or notification as you wait on our site.
    Ask follow up questions if you need to.
  • 100% Satisfaction Guarantee
    Rate the answer you receive.
Ask Mauricio Your Own Question
Mauricio
Mauricio, Technician
Category: Car
Satisfied Customers: 845
Experience:  15 years working in all makes and models
12133139
Type Your Car Question Here...
Mauricio is online now
A new question is answered every 9 seconds

Replace the oil pan gasket

Customer Question

Replace the oil pan gasket
Submitted: 8 years ago.
Category: Car
Expert:  Mauricio replied 8 years ago.
OIL Pan

Special Service Tools



Accessory Belt Detensioner 303-703

Removal
All vehicles
  1. Drain the engine oil.

Vehicles with 2.5L or 3.0L engine

  1. Remove the transfer case.



Vehicles with 2.0L engine

  1. Detach the exhaust link pipe rear retaining clamp.

  1. Remove the link pipe.

  1. Remove the catalytic converter retaining bracket.

  1. Remove the sump to transmission securing bolt.

  1. Slacken but not remove the upper catalyst retaining bracket support securing bolt.

  1. Reposition the catalyst retaining bracket support.



All vehicles

  1. Detach the accessory drive belt.
  1. Using the special tool rotate the belt tensioner counter-clockwise.
  2. Detach the accessory drive belt.

  1. NOTE: Do not remove the A/C compressor upper retaining bolts. Reposition the air conditioning (A/C) compressor.
  1. Remove the A/C compressor lower retaining bolts.
  2. Loosen the A/C compressor upper retaining bolts.

  1. Remove the access cover.



Vehicles with 2.0L engine

  1. Remove the retaining bolt.



Vehicles with 2.5L or 3.0L engine

  1. Remove the retaining bolts.



All vehicles

  1. Remove the oil pan.
    • Remove and discard the gasket.
    • Clean and inspect the oil pan and the cylinder block sealing surfaces using metal surface cleaner or equivalent meeting Jaguar specification WSE-10513392-A.

Installation



All vehicles

  1. NOTE: Apply 10 mm diameter clot of silicone sealant WSE-M4G323-A6 or equivalent meeting Jaguar specification to the engine front cover to the cylinder block mating joints. NOTE: Loosely install the oil pan to transmission housing bolts. NOTE: The oil pan retaining bolts numbered land 2 are longer than the retaining bolts numbered 3 through 15. NOTE: Tighten the oil pan bolts within six minutes of applying sealer. To install, reverse the removal procedure. Install the new oil pan gasket.
    • Complete the tightening sequence.
    • Tighten to 25 Nm .



Vehicles with 2.0L engine

  1. Tighten to 45 Nm .



Vehicles with 2.5L or 3.0L engine

  1. Tighten to 45 Nm .



All vehicles

  1. Tighten to 10 Nm .

  1. Tighten to 25 Nm .



Vehicles with 2.0L engine

  1. Tighten to 25 Nm .

  1. Tighten to 45 Nm .

  1. Tighten to 25 Nm .

  1. Tighten to 55 Nm .

  1. Tighten to 55 Nm .

Vehicles with 2.5L or 3.0L engine

  1. Install the transfer case.

All vehicles

  1. NOTE: Use oil WSE-M2C908-A or equivalent meeting Jaguar specification. Refill the engine with oil.
Customer: replied 8 years ago.
I already complete this on the 3.0 2004 Xtype. Problem is I still can't get to the bolt by trasfer case.
Expert:  Mauricio replied 8 years ago.
give more details?
Customer: replied 8 years ago.
does the engine need to be droped in order to get to all bolt on transfer case side? there is not enough room to remove all bolts.
Expert:  Mauricio replied 8 years ago.

Are you talking about theses bolts?

Related Car Questions