Need Appliance Repair Help? Ask a Technician for Answers ASAP
Good morning! My name is ***** ***** I'll be helping you with your issue today. I’m am one of the experts here on JustAnswer.com. I have been factory trained and one of the best appliance technicians in the industry. We are on the honor system and we only receive credit for or time helping you if you rate our service so please do not forget to rate before you leave or experts like myself won’t be around to help in the future since we must make a living helping you by passing on our knowledge and giving our time. Give me a few minutes to review your appliance issue and write an answer for you.
It sounds like you replaced the suspension rods already and sometimes that can cause this issue, but typically not. The most common problem is a nut below the inner tub that needs to “float”. Floating is when the tub fills up with water to a certain level the inner basket will rise about 1 inch from the center agitator. What this does is disengage the basket from the motor so that the agitator can rotate independently from the basket. If the basket does not float then when it tries to agitate the whole basket will turn back and forth at the same speed as the agitator and this will cause the OL/UL error code.To fix the problem if the basket is not floating you will have to take the washer apart. Below are the steps to follow if you are mechanically able to tackle it:1. Unplug the power cord
2. Lift the top of the washer up, to do this there are 2 latches in the seams between the top and the bottom sections. These latches are about 6 1/2 inches from the right side and left side of the washer. You need to insert a small screwdriver (be careful not to scratch the paint) and push the latch while lifting the top section.
3. The top will actually fold back leaving the inner tube fully exposed. Support the glass lid so it doesn’t get damaged because it is very heavy and will fall open when you flip the top back.
4. Remove the plastic top of the tub. There is one hose connected at the back and there are several snaps around the outer edge that hold it on. Remove the hose and unsnap the snaps and set it aside.
5. Remove the cap covering the very center of the agitator. It is just snapped in place and can be pried off with a small screwdriver.
6. Remove the center screw under the cap.
7. Remove the agitator, you need to lift it evenly and might have to work your way around by pulling on one of the three fins and then the next and so on. I also had luck using a small pair of needle nose pliers and grabbing a small lip inside the area where the screw was and pulling from there.
8. Remove the 6 Phillips screws in the middle holding the plastic top gear in place. Be very careful you don’t drop one of the screws because it can fall through the slots in the basket and be lost below.
9. Remove the plastic top gear.
10. Pull the plastic lower gear off of the splined shaft. It should pull right off.
11. Now you need to pull the basket up and off of the shaft. This is where you might have problems because the basket might be corroded to the shaft. If you can grab the basket on both sides under the outer lip and pull upward it might pull up. If not, then you will have to figure out a way to get it off.
12. Once the basket is off you will notice there is liquid inside of it. That is factory sealed in there so do not worry about that, it is normal.
13. With the basket is off you will be able to see that the shaft is probably corroded and the inside bearing on the basket is corroded. Clean these both off very good and check to see if the basket can easily go back on the shaft and slide up and down without getting stuck. You may need to sand and file the shaft a little bit to get it totally cleaned up. The inner bearing of the basket is plastic so it is pretty easy to clean with light sanding.
14. Reassemble in the reverse order and your done. Check to make sure the basket can easily float now by pulling up on it from the top inside lips.
Again, we are on the honor system here. Please remember to rate my service by selecting a star at the top of the screen before you leave today. If you need anything else, just let me know. You can continue asking follow-up questions at no additional charge after rating my service if you still need assistance.
The fuse is right there where the arrow is pointing you need to remove the console to get at the board.
Sorry I think another expert accidentally replied and meant to reply to a different customer since there is no fuse on this machine. I apologize about the confusion.
Hello again. I'm just following up because I haven't heard back from you and I see this question is still open. Is there anything else I can help you with?
If the basket moved up and down and you replaced the shocks, your main bearing and seal would need to be replaced because it's creating too much friction causing the washer to think it's not balancing. Below is a link to a video that shows you how to replace the part.
CLICK HERE for video
ok good luck.