How JustAnswer Works:
  • Ask an Expert
    Experts are full of valuable knowledge and are ready to help with any question. Credentials confirmed by a Fortune 500 verification firm.
  • Get a Professional Answer
    Via email, text message, or notification as you wait on our site.
    Ask follow up questions if you need to.
  • 100% Satisfaction Guarantee
    Rate the answer you receive.
Ask Appliance Medic Your Own Question
Appliance Medic
Appliance Medic, Home Appliance Technician
Category: Appliance
Satisfied Customers: 10831
Experience:  Factory Trained CFC Technician
13570846
Type Your Appliance Question Here...
Appliance Medic is online now
A new question is answered every 9 seconds

Have Maytag washer dryer combo not filling with water but

Customer Question

Have Maytag washer dryer combo not filling with water but will run through cycles. Have replace witch that controls water input, still not working
Submitted: 1 year ago.
Category: Appliance
Expert:  Appliance Medic replied 1 year ago.

Hi, what is the model number?

Customer: replied 1 year ago.
LSG 1000
Expert:  Appliance Medic replied 1 year ago.

What part numbers have you replaced so far?

Thanks

Customer: replied 1 year ago.
Water Level Switch PS2017307
Customer: replied 1 year ago.
Not sure if you recieved last transmission???
Expert:  Appliance Medic replied 1 year ago.

Hi, is the pressure switch hose clear?

Customer: replied 1 year ago.
I blew air through it. No restriction on air flow
Expert:  Appliance Medic replied 1 year ago.

The water valve is not getting 110v at any point then correct?

Customer: replied 1 year ago.
Apparently. Did not actually check with multimeter
Expert:  Appliance Medic replied 1 year ago.

Are you able to verify? If it's not getting 110v, the control is going to be the culprit or a broken wire. Check the wires from the valve to the board for continuity. If the wires are good, replace the board because it's not sending power to the water valve. We work on the honor system here at Just Answers. Were not credited for our work until you rate our answers positively. After you rate our answers positively the question does not close. You can come back and ask follow up questions for no additional charge.

Expert:  Appliance Medic replied 1 year ago.

Thanks

Customer: replied 1 year ago.
Are you talking about the little board that is on top of water valve or the board that is on the the dryer and controls all the functions of the machine
Expert:  Appliance Medic replied 1 year ago.

The main board. Have you inspected it for burn marks? It's the only other thing besides the pressure switch. We work on the honor system here at Just Answers. Were not credited for our work until you rate our answers positively. After you rate our answers positively the question does not close. You can come back and ask follow up questions for no additional charge.

Customer: replied 1 year ago.
No. I had just pulled it out to change the water hose and when I went to use it after, it was not working???? I will check the board
Expert:  Appliance Medic replied 1 year ago.

Yes, that's strange. Sounds like the board or wire connection on it or near it is shorted possibly?

We work on the honor system here at Just Answers. Were not credited for our work until you rate our answers positively. After you rate our answers positively the question does not close. You can come back and ask follow up questions for no additional charge.

Customer: replied 1 year ago.
Just took off front board and no visible signs of burn
Expert:  Appliance Medic replied 1 year ago.

Do you see where the water valve wires connect?

Customer: replied 1 year ago.
On the water inlet itsself or on the board?
Expert:  Appliance Medic replied 1 year ago.

On the board? Follow the wires from the valve.