Need Appliance Repair Help? Ask a Technician for Answers ASAP
Hello from our service,
My name is Chas, I am so happy to help you today.Before we get started, I would like to help us get on the same page so that our interaction will go smoothly.I might give you an answer immediately, or ask you a question. Either way, we are likely to be in a question and answer format, so you will need to click reply to expert if:a. You want to add detail.b. Your question was not fully answered.c. You want to ask further questions.Since I am inviting you back to do any of these, do not use a 1 or 2 rating or this will likely NOT help you get a satisfactory answer. It will delay our task, and it tends to be depressing for the expert trying to help you, often right at the beginning of the exchange, before we have accomplished our task.I know the rating system is somewhat complicated, but you do not have to do a negative rating in order not to pay or to get your deposit back.In addition, a negative rating only serves to rate the expert doing his/her utmost to help you. The expert also will not get paid under these circumstances.Negative ratings do not cover site problems, delays, or anything else on the site that might annoy you, as experts are only involved in trying to answer your questions.Negative ratings do not cover posts that do not come through, or any other difficulties...experts face those just as you do. This includes frustrations that you might have had before meeting your expert.I would like to say that we are also on the honors system. I in good faith am going to do my utmost to ensure your satisfaction. But, it is up to your honor to click a smiley face and make sure that I am compensated for my time and effort. Please realize we are only compensated PER smiley per click and from bonuses, so extensive time with you would hopefully stimulate your consideration of this aspect of the system.
Have you checked the large pulley underneath to see if it is loose?
I just checked the pulley, and it is tight.
No. Can you tell me?
Thanks. I'll look into this this evening as I must go to work now. I'll get back with you later. Thanks again.
All I ask of you is to please rate me with one of the top 3 ratings. If there is anything else I can help you with today just let me know. You can continue asking questions for as long as you like even after you rate me. Click the continue conversation link if you would like to continue this conversation. If you are done and rate a 1 or 2 star please consider using the "continue conversation" link and telling me what more I can do or what more you would have liked that was within my power so that I possibly give you that information or help me improve my customer satisfaction rating. . .
Bonuses are welcome if I have helped you a lot, however they are not mandatory
Chas, I lost the link to the tech sheet.
Here is what I found: F7 and E5.
I had this same part replaced when the machine was under warrant. What's up with this? Any ideas?
Thanks for your help!!!
Are you still available to answer questions.
My washer is slow to move in the wash cycle. After sensing it sits and does nothing but later moves on and washes and completes cycles.
I stopped the washer to look in the tub to see if there was any change in the clothes. There was no change in the clothes and the water level looked OK. I pushed the start and there was a little clicking. I left the machine and checked back later and found it spinning and shortly finished all cycles. The noise did not last long.
The slow action has happened several times.
I attempted to use the tech sheet from before but it was not available, so no I have no codes.
I have two sets of lights.
sensor, rinse, spin, done
All I ask of you is to please rate me with one of the top 3 ratings. If there is anything else I can help you with today just let me know. You can continue asking questions for as long as you like even after you rate me. Bonuses are welcome if I have helped you a lot, however they are not mandatory
I think I see now how to read the chart. Please look again to see if you're on the correct one. Won't the "rinse and done" be E5?
Okay, now that code would not have been held over for 11 months ago would it?
So, what you're saying is, when I replace the shifter and after I use the washer 3 times there should be no more code (assuming the shifter is not faulty). Right?
Thank you for all you time and help.
I got my shifter. When I replaced the old one, I (with the help of my wife) only tilted the washer to make the change. When I did this it seemed that there was water in the machine's tub. There was no water in the wash tub.
After making the replacement, I ran the "Drain and Spin" cycle. Thinking there was water that could be removed. The washer ran properly, but only a few drops came out of the drain hose.
I did the fault and error test and had the shifter and out of balance codes only. I did not attempt to run the washer again.
My question is "is this normal"?