How JustAnswer Works:

  • Ask an Expert
    Experts are full of valuable knowledge and are ready to help with any question. Credentials confirmed by a Fortune 500 verification firm.
  • Get a Professional Answer
    Via email, text message, or notification as you wait on our site.
    Ask follow up questions if you need to.
  • 100% Satisfaction Guarantee
    Rate the answer you receive.

Ask Randy Your Own Question

Randy
Randy, Home Appliance Technician
Category: Appliance
Satisfied Customers: 1300
Experience:  25 years of overall experience: Owner and technician of own appliance repair business.
18559950
Type Your Appliance Question Here...
Randy is online now
A new question is answered every 9 seconds

Have a Sears Electric Range Model #665.95014102. Used self

Customer Question

Have a Sears Electric Range Model #665.95014102. Used self cleaning cycle tonight and now shows E1 error F5. Can I fix this or do I have to call a Sears technician.
Submitted: 3 years ago.
Category: Appliance
Expert:  Randy replied 3 years ago.
Hello, my name is Randy and I am here to assist you. First your range is actually made by Whirlpool and that is important especially with the error code you described. The problem is with your door latch circuit. I am sending you a chart and how to test the area for you to fix it yourself. Just look down the chart till you see F5 E1 and it will tell you exactly what to do. By doing it yourself you will definitely safe ALOT of time and money. Hope this helps and I am here for further assistance. Thank you, Randy.


WHIRLPOOL FAULT CODES

Whirlpool Range / Stove / Oven Fault Codes
Failure Code Fault Code Description Solution
4 Digit Failure Codes (for 2 digit codes see below)
F1 - E0 EEPROM communication error 1. Disconnect power for at least 30 seconds.
2. Re-apply power and observe for at least one minute.
3. If code re-appears, replace control board (also called ERC or clock).

Note: Applies to all F1-E... codes except F1-E3.
F1 - E1 EEPROM checksum error
F1 - E2 UL A/D error(s)
F1 - E4 Model ID error
F1 - E5 Calibration shifted
F1 - E6 Latch signal mismatch error
F1 - E9 Stack overflow
F1 - E3 Wiring harness cavity size does not match previously stored value The "Cavity Size Select" jumpers in the wiring harness indicate a cavity size different from that which the control was previously configured for. Check the jumpers in the harness to make sure they agree with the actual oven size.
F2 - E0 Shorted keypad (also called touch pad) 1. Check keypad connector for firm connection (keypad connects to control board).
2. Press CANCEL. If error code returns after 60 seconds, replace keypad (also called touch pad or membrane switch). Some models incorporate keypad in to control board as one unit. In this case, replace control board (also called ERC or clock).
F2 - E1 Keypad cable unplugged
F2 - E5 Cancel key drive line open
F2 - E6 Cancel key drive line open
F3 - E0 Oven temperature sensor (RTD) opened (upper oven, if double oven) Replace Oven temperature sensor (RTD)

Note: Applies to all F3-E... codes.
F3 - E1 Oven temperature sensor (RTD) shorted (upper oven, if double oven)
F3 - E2 Oven temperature is too high (Cook mode)
F3 - E3 Oven temperature is too high (Clean mode)
F3 - E4 Oven temperature sensor (RTD) opened (lower oven, if double oven)
F3 - E5 Oven temperature sensor (RTD) shorted (lower oven, if double oven)
F3 - E6 Warming drawer sensor open
F3 - E7 Warming drawer sensor shorted
F4 - E1 Meat probe malfunction - shorted Problem could be with the probe, the receptacle, or probe circuit. Check probe. Look for pinched wire. Look for condensation or contamination on probe receptacle. Replace probe if all else checks out ok.
F5 - E0 Door switches do not agree (condition exists when door switch is closed indicating an open door, and latch switch is closed indicating a locked door) 1. If door latched:
  1. Disconnect power from unit.
  2. Check wires and connectors from control to door switch, then from door switch to control. If no damage to wires and all connectors okay, proceed to step C.
  3. Replace door switch.
  4. Re-apply power.
  5. Press and hold any key down for 1 minute to clear F5 failure code from memory. F2 will appear. Press CANCEL and observe for 1 minute to ensure operation is correct.

2. If door not latched:

  1. Disconnect power from unit.
  2. Check wires and connectors from control to latch switch, then from latch switch to control. If no damage to wires and all connectors okay, proceed to step C.
  3. Repeat steps A and B for door switch.

3. Measure door switch (door open = switch open small low voltage terminals). Replace switch if defective.
4. Measure latch switch (unlatch = switch open, CAUTION - oven light contacts are closed). Replace switch if defective.
5. If corrections are made in any step, reconnect power to control. Press and hold any key for 1 minute to clear R failure code from memory. F2 will appear. Press CANCEL and observe for 1 minute to ensure operation is correct.
6. If failure remains, disconnect power and replace control.

Note: Applies to all F5-E... codes.

F5 - E1 Self clean latch will not lock
F5 - E2 Latch during CLEAN error
F5 - E5 Self clean temperature not reached within 45 minutes.
F5 - E6 Door is open, but latch is locked
F5 - E7 Self clean latch will not unlock
F6 - E0 Return line not connected If switch pulse return line is not connected, electronic control will display F6 within 60 seconds after power up. Replace control.
F7 - E1 Common switch wire is defective Common wire (+5VDC) to latch switch, and to door switch is shorted to chassis ground or neutral. A double oven will have two of each switch and one common wire.
1. Check connections at control and at the latch switch and door switch.
2. If all connections are good, then check the individual switches as outlined for the F5 failure.
2 Digit Failure Codes
F0 Board failure Replace control board (also called ERC or clock).
F1 Board failure Replace control board (also called ERC or clock).
F2 Oven temperature is too high 1. Look for welded relay contacts on bake or broil relays. If this happens, replace oven control (also called clock or ERC).
2. For SELF CLEAN models: check door lock operation.
3. Look for a high resistance connection or any other cause of high resistance in the oven temperature sensor circuit. Check sensor, sensor harness and sensor harness connection at sensor and oven control. Replace sensor if found defective.

Remember: Oven control (ERC) measures resistance of sensor circuit, not actual oven temperature.
F3 Oven temperature sensor (RTD) open Replace Oven temperature sensor (RTD)
F4 Oven temperature sensor (RTD) shorted Replace Oven temperature sensor (RTD)
F5 Board failure Replace control board (also called ERC or clock).
F7 Function key stuck on ERC Replace control board (also called ERC or clock).
F8 Board failure Replace control board (also called ERC or clock).
F9 Oven door lock failure Check wiring to door lock switch (the wire harness may be connected wrong). Check for stuck lock switch.
Find Parts



Customer: replied 3 years ago.
This does not help. Says latch will not lock. It is locked and will not unlock. Also does not tell you how to do this things it says and to proceed to step C if it does not work. No step C. I'll have to call a technician.

JustAnswer in the News:

 
 
 
Ask-a-doc Web sites: If you've got a quick question, you can try to get an answer from sites that say they have various specialists on hand to give quick answers... Justanswer.com.
JustAnswer.com...has seen a spike since October in legal questions from readers about layoffs, unemployment and severance.
Web sites like justanswer.com/legal
...leave nothing to chance.
Traffic on JustAnswer rose 14 percent...and had nearly 400,000 page views in 30 days...inquiries related to stress, high blood pressure, drinking and heart pain jumped 33 percent.
Tory Johnson, GMA Workplace Contributor, discusses work-from-home jobs, such as JustAnswer in which verified Experts answer people’s questions.
I will tell you that...the things you have to go through to be an Expert are quite rigorous.
 
 
 

What Customers are Saying:

 
 
 
  • Thank you for the expeditious answer. It's good to know you're out there and awake in the wee hours when I finally have time to ask questions about my Jenn Air. Jean Riverhead, NY
< Last | Next >
  • Thank you for the expeditious answer. It's good to know you're out there and awake in the wee hours when I finally have time to ask questions about my Jenn Air. Jean Riverhead, NY
  • You did one super job of explaining to me everything there is to know about this fridge. I'm looking forward to asking you questions in the future. Jimmy Bagley, IA
  • Wonderful service, prompt, efficient, and accurate. Couldn't have asked for more. I cannot thank you enough for your help. Mary C. Freshfield, Liverpool, UK
  • This expert is wonderful. They truly know what they are talking about, and they actually care about you. They really helped put my nerves at ease. Thank you so much!!!! Alex Los Angeles, CA
  • Thank you for all your help. It is nice to know that this service is here for people like myself, who need answers fast and are not sure who to consult. GP Hesperia, CA
  • I couldn't be more satisfied! This is the site I will always come to when I need a second opinion. Justin Kernersville, NC
  • Just let me say that this encounter has been entirely professional and most helpful. I liked that I could ask additional questions and get answered in a very short turn around. Esther Woodstock, NY
 
 
 

Meet The Experts:

 
 
 
  • John

    Home Appliance Technician

    Satisfied Customers:

    13453
    Appliance repair business owner for over 43 years.
< Last | Next >
  • http://ww2.justanswer.com/uploads/docjohn174/2008-12-13_170143_johnask.jpg John's Avatar

    John

    Home Appliance Technician

    Satisfied Customers:

    13453
    Appliance repair business owner for over 43 years.
  • http://ww2.justanswer.com/uploads/tomgoe/2011-01-04_021913_2008-03-03_183612_phpexrmok_c2pm.jpg Tom Goellner's Avatar

    Tom Goellner

    Home Appliance Technician

    Satisfied Customers:

    1293
    32 yrs. experience servicing major appliances and HVAC equipment.
  • http://ww2.justanswer.com/uploads/MD/md2020/2012-6-6_20648_Selfpic.64x64.jpg Tyler Z.'s Avatar

    Tyler Z.

    Appliance Doc

    Satisfied Customers:

    58693
    9+ years being an appliance technician with factory training.
  • http://ww2.justanswer.com/uploads/SM/smitty1486/2011-3-1_0145_Snapshotofme1.64x64.png Kelly's Avatar

    Kelly

    Appliance Technician

    Satisfied Customers:

    8783
    Highly accurate diagnostician with over 30 years experience!
  • http://ww2.justanswer.com/uploads/AP/appliance medic/2012-6-8_212544_Image4.64x64.jpg Appliance Medic's Avatar

    Appliance Medic

    Home Appliance Technician

    Satisfied Customers:

    7932
    Factory Trained CFC Technician
  • http://ww2.justanswer.com/uploads/TE/Teamcold/2012-6-15_15028_HomeRepairsquarecopy.64x64.jpg Barry G.'s Avatar

    Barry G.

    Home Appliance Technician

    Satisfied Customers:

    6113
    27 years in home appliance repair. EPA refrigerant transition and recovery certification type I & II.
  • http://ww2.justanswer.com/uploads/TH/TheHomeSmithy/2011-8-13_11146_homesmithy.500x500.64x64.jpg The Home Smithy's Avatar

    The Home Smithy

    Home Appliance Technician

    Satisfied Customers:

    6081
    30 years repairing appliances
 
 
 

Related Appliance Questions

Chat Now With An Appliance Technician
Randy
Randy
Appliance Technician
1300 Satisfied Customers
25 years of overall experience: Owner and technician of own appliance repair business.