How JustAnswer Works:

  • Ask an Expert
    Experts are full of valuable knowledge and are ready to help with any question. Credentials confirmed by a Fortune 500 verification firm.
  • Get a Professional Answer
    Via email, text message, or notification as you wait on our site.
    Ask follow up questions if you need to.
  • 100% Satisfaction Guarantee
    Rate the answer you receive.

Ask Bryan Your Own Question

Bryan
Bryan, Home Appliance Technician
Category: Appliance
Satisfied Customers: 11973
Experience:  15 yrs. experience as a certified appliance technician.
10522817
Type Your Appliance Question Here...
Bryan is online now
A new question is answered every 9 seconds

Our oven is not turning on since we unplugged it to shut off

Resolved Question:

Our oven is not turning on since we unplugged it to shut off an f2 beep during self cleaning. The clock and light work, but nothing else does. Should we restart it somehow?
Submitted: 5 years ago.
Category: Appliance
Expert:  Bryan replied 5 years ago.
can you give me make and model? I will look up code for you, thanks Bryan
Customer: replied 5 years ago.
GE profile built in electric convection oven
Model JTP16 made in 1996
Expert:  Bryan replied 5 years ago.
these are the fault codes for your oven, it say you have a bad sensor , this may or may not have had to do with unplugging oven it just may have been ready to fail. hope this helps Bryan.
FAULT CODES - Table of Contents
ADMIRAL
Range/Stove/Oven Fault Codes
AMANA
Range/Stove/Oven Fault Codes
Dual Convection Wall Oven
"Big Oven" 5.1 cubic ft. (Sigma Touchmatic ERC)
ASKO
Dishwasher
Dryer
Washing Machine
CALORIC
Range/Stove/Oven Fault Codes
RST376 Gas Range Fault Codes
CROSLEY
DACOR
Range/Stove/Oven Fault Codes
FRIGIDAIRE
Range/Stove/Oven Fault Codes Version 1
Range/Stove/Oven Fault Codes Version 2
Range/Stove/Oven Fault Codes Version 3
Range/Stove/Oven Fault Codes Version 4
GE
Gas or Built In Oven Fault Codes
XL44 Self Clean Oven Fault Codes
"New '99" Range/Stove/Oven Fault Codes
Range/Stove/Oven Fault Codes
WSL Model Washing Machine
Microwave Fault Codes
Dishwasher Fault Codes - From Late 1990's forward
GIBSON
Range/Stove/Oven Fault Codes
HAMILTON
Range/Stove/Oven Fault Codes
HARDWICK
HOTPOINT
Range/Stove/Oven Fault Codes
JENN AIR
Range/Stove/Oven Fault Codes
Newer Style Range/Stove/Oven Fault Codes
KELVINATOR
KITCHEN AID
Range/Stove/Oven Fault Codes
MAGIC CHEF
Range/Stove/Oven Fault Codes
MAYTAG
Gemini Range/Stove/Oven Fault Codes
Type "C" and "D" Clocks Range/Stove/Oven Fault Codes
Range/Stove/Oven Fault Codes
Stackable A/W and Dryer Fault Codes
NORGE
RCA
Range/Stove/Oven Fault Codes
ROPER
Range/Stove/Oven Fault Codes
Range/Stove Oven - Alternative 2 Digit Fault Codes
Range/Stove Oven BES, BEP models
Range/Stove 24" Built-In Self-Clean Wall Oven
SEARS/KENMORE
Range/Stove/Oven Manufacturers
TAPPAN
Range/Stove/Oven Fault Codes
THERMADOR
Range/Stove/Oven Fault Codes starting with an E
Range/Stove/Oven Fault Codes starting with an F
WESTINGHOUSE
Range/Stove/Oven Fault Codes
WHIRLPOOL
Whirlpool Polara
Range/Stove/Oven Fault Codes Non Y-Line
Range/Stove/Oven Fault Codes, Common
Range/Stove Oven 30" Free-standing, Models SF3...& 24" Built-In
Whirlpool Duet & Duet HT
Calypso Washing Machine
Calypso Matching Dryer

ADMIRAL
Range/Stove/Oven Fault Codes
Failure
Code
ConditionCheck/Repair
F1Defective touch pad or membraneReplace touch pad or clock assembly (also called the ERC) (usually the touch pad)
F1Watchdog on boardReplace touch pad or clock assembly (also called the ERC)
F2Oven too hotReplace relay board (if present) or oven temperature sensor
F3 or F4Open or shorted oven temperature sensor Replace oven temperature sensor
F5Hardware and watchdog circuits disagreeReplace clock assembly (also called the ERC)
F6Missing AC signalCheck for proper voltage
F7Function key shorted or stuck buttonReplace touch pad or clock assembly (also called the ERC) or un-stick button
F8Analog/Digital troubleReplace clock assembly (also called the ERC)
F9Door latch troubleCheck door lock circuit or replace clock assembly (also called the ERC)
F0Function key stuck Replace touch pad or clock assembly (also called the ERC)
Back to TABLE OF CONTENTS

AMANA
Range/Stove/Oven Fault Codes

Failure Code - glass link Electronic Range Control (ERC)ConditionCheck/Repair
Door flashing #0, 1, 2, 3 Latch switch broken Replace
Lock flashingLatch switch brokenReplace
F0Loss of safety signal Replace adapter board
F1Watchdog circuit Replace Electronic Range Control (ERC)
F2Oven too hotReplace oven temperature sensor
F3 F4Open or shorted oven temperature sensorReplace oven temperature sensor
F7Shorted touch panelReplace glass panel
F9Motorized doorCheck latch
FFLock error Check switch and motor
Electronic Range Control (ERC) III / Relay board with separate board / push buttons
F0 Shorted push pad Replace
F1Failed Electronic Range Control (ERC)Replace
F2Oven too hotReplace oven temperature sensor
F3 F4 Shorted or open oven temperature sensorReplace oven temperature sensor
F5, F6, F8Failed Electronic Range Control (ERC)Replace ERC
F7Shorted or sticking buttonCheck glass alignment, replace touch panel if necessary
F9Door latch failure Replace door latch switch or assembly if necessary
Back to TABLE OF CONTENTS
AMANA
Dual Convection Wall Oven
Failure Code ConditionCheck/Repair
F0 Shorted touch pad Replace touch pad
F1Electronic range control failureReplace electronic range control (ERC)
F2Oven temperature 100 degrees over limitReplace oven temperature sensor
F3Shorted oven temperature sensorReplace oven temperature sensor
F4Open oven temperature sensorReplace oven temperature sensor
F6Electronic range control component failureReplace electronic range control (ERC)
F7Failure detected in self-clean lock circuitry Check door latch mechanism
Back to TABLE OF CONTENTS
AMANA
"Big Oven" 5.1 cubic ft. (Sigma Touchmatic ERC)
Failure Code ConditionCheck/Repair
F0-0No Error Initial factory setting
F1-1Over temperature while cookingCheck oven temperature sensor and wiring first, replace control board if oven temperature sensor is good
F1-3Over temperature while cleaningCheck oven temperature sensor and wiring first, replace control board if oven temperature sensor is good
F1-5Cancel key input out of rangeReplace control board
F1-7Keyboard disconnected Verify wire connection is tight.Replace control if failed
F1-8Shorted keyReplace control board
F1-9Slave micro not functioningReplace control board
F1-ACircuit board groundingReplace control board
F1-C Control not calibratedReplace control board
F1-ECircuit board data corruption Replace control board
F1-F Circuit board data corruption Replace control board
F1-HDoor switch input circuit failureCheck switch and wiring
F1-JLatch switch input circuit failureCheck switch and wiring
F3-1Oven temperature sensor or oven temperature sensor circuit failureCheck wire connections and oven temperature sensor
F9-1Auto latch will not lockCheck wiring, motor, and latch switch
F9-2 Auto latch will not unlock Check wiring, motor, and latch switch
Back to TABLE OF CONTENTS
Asko
Dishwasher
Failure
Code
ConditionCheck/Repair
F1 Water heating fault, selected temperature not reached within 60 minutes · Incoming water temperature too cool
· Heating element burned out
· Thermostat defective
F2High water level· Plugged/Bad water pump
· Defective water inlet valve
F3Thermistor fault· Open thermistor
· Bad wiring to thermistor
F4Fault with water fill (only on machines with level-controlled fill)

Note: Lights blinking, pump running and controls dead indicates an over fill fault
1. Disconnect the power to the unit

2. Remove the lower access panels and check the tray under the dishwasher (you will probably find it is full of water)

3. Use a towel or a sponge to remove the water

4. There is a float that should stop the operation of the dishwasher and run the pump if water is in this tray. Check this pump to see if it is functional

5. Test the dishwasher

6. If there are no leaks from the dishwasher into the pan, check the drain hose under the sink

7. THE DRAIN HOSE MUST RUN UP TO THE TOP OF THE UNDERSIDE OF THE COUNTERTOP THEN DOWN TO THE DRAIN. (If the hose is not set up like this, water from the sink drain will flow into the dishwasher and overfill the tray

*Faults may vary by model. Use this as a general guide.
Back to TABLE OF CONTENTS
Asko
Dryer
Failure
Code
ConditionCheck/Repair
F1 Condensate drain overfillingCheck condensate reservoir pump and drain tube.
F2Maximum drying time exceeded (3hrs) · Check for tripped circuit breaker or blown fuse
· Check ductwork for lint build-up
· Check hi-limit and cycling thermostat
· Check heating element
F3Thermistor fault · Open thermistor, replace
· Bad wiring to thermistor
F4Too much lint in the lint filter, front housing, or in the condenserClean lint from lint filter and/or condenser
F5Fault in the moisture sensor · Lint covering sensor in front of housing
· Bad sensor
· Bad wiring to sensor
Back to TABLE OF CONTENTS
Asko
Washing Machine
Failure
Code
ConditionCheck/Repair
F1 Water supply/low water fill · Check water supply to machine
·Replace water inlet valve
F2Water level too high· Plugged/Bad water pump
· Faulty water valve
F3Pump problem Check pump trap and clean.
F4Thermistor problem· Open thermistor, replace
· Bad wiring to thermistor
F5Fault in thermal cutout or heating pause fault. Selected temperature not reached in 90 minutes· Check heating element
· Check thermostat
F6Motor fault· Check wiring to motor
· Replace motor if necessary
F7Door lock release fault· Bent pull-rod for door latch
· Bad door latch solenoid
00 00 Machine did not spin Check load for out of balance Redistribute load and restart
Back to TABLE OF CONTENTS
CALORIC
Range/Stove/Oven Fault Codes
Failure Code - glass link Electronic Range Control (ERC)ConditionCheck/Repair
Door flashing #0, 1, 2, 3 Latch switch broken Replace switch
"Lock" flashingLatch switch brokenReplace switch
F0Loss of safety signalReplace adapter board
F1Watchdog circuitReplace Electronic Range Control (ERC)
F2Oven too hot Check oven temperature sensor
F3 F4 Open or shorted oven temperature sensor Replace oven temperature sensor
F7Shorted touch panel Replace touch panel
F9Motorized door problem Check door latch
FFDoor lock error Check door switch and latch motor
Electronic Range Control (ERC) III / Relay board with separate board / push buttons
F0 Shorted touch pad Replace touch pad
F1Failed Electronic Range Control (ERC)Replace ERC
F2Oven too hotCheck oven temperature sensor, replace if necessary
F3 F4Shorted or open oven temperature sensor Replace oven temperature sensor
F5, F6, F8Failed Electronic Range Control (ERC)Replace ERC
F7Shorted or sticking buttonCheck glass touch panel alignment, replace if necessary
F9Door latch failure Replace door latch if necessary
Back to TABLE OF CONTENTS
CALORIC
RST376 Gas Range Fault Codes
Failure
Code
ConditionCheck/Repair
F1Clock bad Replace clock assembly (also called the ERC)
F2Oven temperature sensor defectiveReplace oven temperature sensor
F3Open oven temperature sensorReplace oven temperature sensor
F4Oven temperature sensor low ratingReplace oven temperature sensor
F5Clock failure Replace clock assembly (also called the ERC)
F6Power surge (clock)Try turning off power to appliance for one minute. If problem persists, replace clock assembly (also called the ERC)
F7Touch panel button stuckReplace touch panel (membrane)
F8Failure of diagnostic read-out Replace clock assembly (also called the ERC)
Back to TABLE OF CONTENTS
DACOR
Range/Stove/Oven Fault Codes
Failure
Code
ConditionCheck/Repair
F0Clock pushbutton is stuck in a depressed position Check clock buttons
F1Element relay circuit failureControl board may be bad
F2Oven temperature exceeded the clean runaway temperature (self clean only) or the cooking runaway temperature (cooking modes only)Call for service
F3Short Circuit in the oven temperature sensor Check oven temperature sensor for continuity, if no resistance (zero ohms), replace
F4Short Circuit in the oven temperature sensorCheck oven temperature sensor for continuity, if no resistance (zero ohms), replace
F6Failure in the EEPROM check comparison (only time of day and timer will operate)Call for service, electronic clock control is usually the cause of the problem
F7Failure of the self- clean automatic door latch systemCheck door latch and switch(es)
F8Failure of the door latch motor. Occurs when the motor runs for two minutes without the door locking in self-clean modeCheck door lock motor and door latch
Back to TABLE OF CONTENTS
FRIGIDAIRE
Range/Stove/Oven Fault Codes Version 1
Failure
Code
ConditionCheck/Repair
F2Oven temp is above design specificationsOven temp has risen above 665F and door unlocked or above 965F with door locked. Check oven temperature sensor.
F3The oven temperature sensor is openCheck for open wire connection between EOC (Electronic Oven Control - Clock) and the oven temperature sensor. Replace sensor if no wiring problem.
F4The oven temperature sensor is shortedCheck for shorted wire and/or connections between the EOC (Electronic Oven Control - Clock) and the oven temperature sensor. Replace sensor if no wiring problem.
F5The watchdog is active when it should be offMicroprocessor checking the operation of the EDC relay, after selection of bake, broil, or clean operation. Relay failed this check.
F6No 60 Hz time base 60 Hz time base is required for time controlled cycling. Replace EDC.
F7Lock motor relay watchdog circuit is active when it should be off Microprocessor checking the operation of the EDC lock, relay failed. Replace EDC.
F8Lock motor relay watchdog is active when it should be off Microprocessor checking the operation of the EDC lock relay after self clean is selected, relay failed. Replace EDC.
Back to TABLE OF CONTENTS
FRIGIDAIRE
Range/Stove/Oven Fault Codes Version 2
Failure
Code
ConditionCheck/Repair
F0 & F1 EOC (Electronic Oven Control) failure Replace
F2Oven too hot Check Bake function
F3Oven temperature sensor openCheck oven temperature sensor, 1100 ohms
F4Oven temperature sensor shortedReplace component
F5, 6, 7 EOC (Electronic Oven Control) failureReplace component
F8 Lock switchesCheck or Replace component
Back to TABLE OF CONTENTS
FRIGIDAIRE
Range/Stove/Oven Fault Codes Version 3
Failure
Code
ConditionCheck/Repair
F0 & F1 EOC (Electronic Oven Control) failure Replace EOC (Electronic Oven Control)
F2Oven too hot Likely a bad oven temperature sensor (should read 1100 ohms) Possible bad EOC (Electronic Oven Control)
F3Oven temperature sensor openReplace oven temperature sensor
F4Oven temperature sensor shorted Replace oven temperature sensor
F5 or F6 or F7EOC (Electronic Oven Control) failure Replace EOC(Electronic Oven Control)
Back to TABLE OF CONTENTS
FRIGIDAIRE
Range/Stove/Oven Fault Codes Version 4
Failure
Code
ConditionCheck/Repair
F1Circuit board defectiveReplace control board
F2 1. The oven temp has risen above 665F and the door is not locked or
2. The temp has risen above 965F with the door locked
1. Check oven temp in mode that failure occurred. Replace EOC (Electronic Oven Control) if above limits
2. Check 8-pin connector. Check and replace oven temperature sensor if necessary
F3Oven temperature sensor is open (above 3000 ohms)Check resistance of oven temperature sensor, check for open wiring between oven temperature sensor and control
F4 Oven temperature sensor is shorted (below 500 ohms)Check resistance of oven temperature sensor, check for shorted wiring between oven temperature sensor and control
F5Internal watchdog circuit has detected a failureDefective EOC (Electronic Oven Control)
F6 Shorted buttons Check push buttons and dome switches on control
F8 Logic interrupted (lock motor switch sequence)Check door lock switches and wiring
Back to TABLE OF CONTENTS
GE
Gas or Built In Oven Fault Codes
Failure
Code
ConditionCheck/Repair
F0 or F1 Failed transistor in controlIf code cannot be cancelled, replace the Electronic Range Control (ERC) or touch pad
F2Oven over temp - exceeded 590F with door in unlocked position or 990F with door lockedIf actual temp condition occurred, look for welded relay contacts or high resistance connection or any cause in the oven temperature sensor circuit
F3Open oven temperature sensor circuit Measure oven temperature sensor circuit at oven temperature sensor (should be approx 1100 ohms at room temp); check for cut or pinched wire or loss of contact
F4Shorted oven temperature sensor circuit Same as above; check for melted connector or both leads shorted to ground
F8 Component failure within Electronic Range Control (ERC) effecting temp processing circuitsReplace Electronic Range Control (ERC)
F9 Problem with door lock circuit such as pinched wire between Electronic Range Control (ERC) and door lock switchCheck wiring and test operation of switch
Back to TABLE OF CONTENTS
GE
XL44 Self Clean Oven Fault Codes
Failure
Code
ConditionCheck/Repair
F0 - F1 - F7Stuck keypad may mean relay is turned on. Determine if problem is with the Key Panel or Control by:
1. Pushing CLEAR/OFF pad.
2. Disconnecting Ribbon Cable from control and waiting at least 32 seconds to see if Code recurs

If code recurs, problem is in the control. Replace control.

If code does not recur, problem is with the Key Panel.
F2
Note: Also see fan thermal switches
Indicates that oven is over temperature in one of the following modes within either a cooking or clean mode of operation.
· Control senses oven temperature above 650 degrees F with the door circuit in the unlock mode.
· Control senses oven temperature above 935 degrees F with the door in the locked mode.
· Stalled cooling fan or airflow problem.
· Look for welded relay contacts. (Heating elements on in off mode).
· Look for open thermal switch in lock motor circuit. Switch is normally closed and will open if area overheats due to fan not operating. Look for cause - fan thermal switch not closing, fan stalled, etc.
· Look for high resistance in the oven temperature sensor circuit due to high contact resistance (poor terminal crimp, deformed terminals, loose connection) or intermittent solder joint on control or intermittent oven temperature sensor.
· Look for electrical noise interference in the oven temperature sensor circuit (Ham radio, cordless phone, etc.).
F3 - F4 Open oven temperature sensor (circuit) (over 2700 ohms) or, shorted oven temperature sensor. Could be a result of:
· contamination on terminals
· pinched wire in oven temperature sensor circuit
· cold solder joint on control.
· Disconnect power to range and remove oven temperature sensor connector from control.
· Measure oven temperature sensor resistance at oven temperature sensor connector (take care not to damage terminals in block) - Should read 1100 ohms at room temperature (approx 72 degrees F).
· Measure each oven temperature sensor lead from connector block to ground. If shorted, look for pinched or cut wire in oven temperature sensor circuit.
· Check connector terminals - Look for deformed or corrosion on terminals. Repair or replace.
If all above is ok replace control.
F5Relay safety circuit failure · Check oven temperature sensor circuit for intermittent high resistance.
· Check lock circuit
· Press Clear/Off and reprogram control. If code reappears, replace control

Note: If all above check OK the F5 code can be a result of a momentary loss of power (Do NOT replace control or lock, check lock circuit)
FC Problem with door lock circuit such as pinched wires between control and door lock switches on motorized lock circuits. Check wiring and test operation of switches.
FD Shorted meat probe

Note: Problem can be with the probe or receptacle or meat probe circuit.
· Check probe. Resistance should be 30k ohms to 50k ohms at room temperature.
· Look for pinched wire.
· Look for condensation or contamination of receptacle or nearby installation.
FFLoss of door motor safety circuit Replace control
Back to TABLE OF CONTENTS
GE
"New '99" Range/Stove/Oven Fault Codes
Failure
Code
ConditionCheck/Repair
FFF Control Error, Failed EEPROM Replace Control
F0 or F7Shorted Clear/Off Key due to membrane switch, control or connectorShorted key panel membrane switch; Check Electronic Range Control (ERC)
F2 During BakeControl senses oven temp above 590 degrees FHigh resistance connection in oven temperature sensor circuit. Check Electronic Range Control (ERC) - Welded bake relay contacts
F2 During CleanControl senses oven temp above 915 degrees FHigh resistance connection in oven temperature sensor circuit. Check Electronic Range Control (ERC) - Welded clean relay contacts. Both lock switch 1 & 2 closed at the same time
F3Open oven temperature sensor, oven temperature sensor resistance exceeds 2900 ohms during bake, broil or cleanOven temperature sensor/Oven temperature sensor circuit connections
F4 Shorted oven temperature sensor, oven temperature sensor resistance less than 2900 ohms during bake, broil or cleanOven temperature sensor/oven temperature sensor circuit connections
FFF Door motor safety circuit Electronic Range Control (ERC)
Back to TABLE OF CONTENTS
GE
Range/Stove/Oven Fault Codes
Failure
Code
ConditionCheck/Repair
F0 and F1 Failed Thermistor Control Replace Electronic Range Control (ERC)
F2 Oven temp exceeds 590 w/ unlocked doorHigh resistance or interference in oven temperature sensor. Replace oven temperature sensor
F3Open oven temperature sensor circuit Replace oven temperature sensor
F4Shorted wire (Oven temperature sensor)Locate and correct
F7 A = Function pad button stuck or
B = Bad clock
Unstick button or
Replace Electronic Range Control (ERC)
F8Component Failure Replace Electronic Range Control (ERC)
F9 Program w/ door circuit Check wiring
Back to TABLE OF CONTENTS
Bryan, Home Appliance Technician
Category: Appliance
Satisfied Customers: 11973
Experience: 15 yrs. experience as a certified appliance technician.
Bryan and other Appliance Specialists are ready to help you
Expert:  Bryan replied 5 years ago.
sorry about that didnt mean to paste all of the codes. just scroll down to g.e. .thanks Bryan

JustAnswer in the News:

 
 
 
Ask-a-doc Web sites: If you've got a quick question, you can try to get an answer from sites that say they have various specialists on hand to give quick answers... Justanswer.com.
JustAnswer.com...has seen a spike since October in legal questions from readers about layoffs, unemployment and severance.
Web sites like justanswer.com/legal
...leave nothing to chance.
Traffic on JustAnswer rose 14 percent...and had nearly 400,000 page views in 30 days...inquiries related to stress, high blood pressure, drinking and heart pain jumped 33 percent.
Tory Johnson, GMA Workplace Contributor, discusses work-from-home jobs, such as JustAnswer in which verified Experts answer people’s questions.
I will tell you that...the things you have to go through to be an Expert are quite rigorous.
 
 
 

What Customers are Saying:

 
 
 
  • Thank you for the expeditious answer. It's good to know you're out there and awake in the wee hours when I finally have time to ask questions about my Jenn Air. Jean Riverhead, NY
< Last | Next >
  • Thank you for the expeditious answer. It's good to know you're out there and awake in the wee hours when I finally have time to ask questions about my Jenn Air. Jean Riverhead, NY
  • You did one super job of explaining to me everything there is to know about this fridge. I'm looking forward to asking you questions in the future. Jimmy Bagley, IA
  • Wonderful service, prompt, efficient, and accurate. Couldn't have asked for more. I cannot thank you enough for your help. Mary C. Freshfield, Liverpool, UK
  • This expert is wonderful. They truly know what they are talking about, and they actually care about you. They really helped put my nerves at ease. Thank you so much!!!! Alex Los Angeles, CA
  • Thank you for all your help. It is nice to know that this service is here for people like myself, who need answers fast and are not sure who to consult. GP Hesperia, CA
  • I couldn't be more satisfied! This is the site I will always come to when I need a second opinion. Justin Kernersville, NC
  • Just let me say that this encounter has been entirely professional and most helpful. I liked that I could ask additional questions and get answered in a very short turn around. Esther Woodstock, NY
 
 
 

Meet The Experts:

 
 
 
  • John

    Home Appliance Technician

    Satisfied Customers:

    13442
    Appliance repair business owner for over 43 years.
< Last | Next >
  • http://ww2.justanswer.com/uploads/docjohn174/2008-12-13_170143_johnask.jpg John's Avatar

    John

    Home Appliance Technician

    Satisfied Customers:

    13442
    Appliance repair business owner for over 43 years.
  • http://ww2.justanswer.com/uploads/tomgoe/2011-01-04_021913_2008-03-03_183612_phpexrmok_c2pm.jpg Tom Goellner's Avatar

    Tom Goellner

    Home Appliance Technician

    Satisfied Customers:

    1191
    32 yrs. experience servicing major appliances and HVAC equipment.
  • http://ww2.justanswer.com/uploads/MD/md2020/2012-6-6_20648_Selfpic.64x64.jpg Tyler Z.'s Avatar

    Tyler Z.

    Appliance Doc

    Satisfied Customers:

    51307
    7+ years being an appliance technician with factory training.
  • http://ww2.justanswer.com/uploads/bryanpaul52/2009-2-18_12031_0918081611.jpg Bryan's Avatar

    Bryan

    Home Appliance Technician

    Satisfied Customers:

    11158
    15 yrs. experience as a certified appliance technician.
  • http://ww2.justanswer.com/uploads/SM/smitty1486/2011-3-1_0145_Snapshotofme1.64x64.png Kelly's Avatar

    Kelly

    Appliance Technician

    Satisfied Customers:

    6493
    Highly accurate diagnostician with over 30 years experience!
  • http://ww2.justanswer.com/uploads/TH/TheHomeSmithy/2011-8-13_11146_homesmithy.500x500.64x64.jpg The Home Smithy's Avatar

    The Home Smithy

    Home Appliance Technician

    Satisfied Customers:

    5935
    30 years repairing appliances
  • http://ww2.justanswer.com/uploads/TE/Teamcold/2012-6-15_15028_HomeRepairsquarecopy.64x64.jpg Barry G.'s Avatar

    Barry G.

    Home Appliance Technician

    Satisfied Customers:

    5039
    27 years in home appliance repair. EPA refrigerant transition and recovery certification type I & II.